Table of Content
To seal the plastic, roll the plastic around a plank of wood several times at the bottom and use clamps to hold it together. If necessary because of limited space, place the structure so that it is approximately 1 inch (2.5 cm) from the middle PVC pipe. This will place the legs of the ladder inside the booth, but they will be covered by plastic.
To save your hands, pick up a box of Nitrile gloves. Use them whenever you are using chemicals like thinner, and mixing or spraying paint. I even wear them when doing bodywork to save my hands and to keep oil from my hands from getting on the paint surface.
How much area does 5000 lumens cover
About how long does this take to set up and tear down? I live in West Texas where it is very sandy and windy. Make sure to invest in several disposable paint suits with hoods. Wear one when priming to protect you from the paint. Most of the dust that will get into a paintjob will come from the painter. Ducting is a must and should be designed to suit you fan, air velocity is critical to performance.

Place the sprayer in the center of the spray booth. Paint your project according to your chosen paint scheme. Use light, even strokes to avoid drips and runs.
Choosing A Blower For The Hobby Spray Booth
Remember the “rules” I mentioned at the beginning? Below are some simple rules that can certainly help you achieve great results. Yes, it is possible to get smooth, clean clearcoat in your home shop.

A few pieces of well-placed tape can act as closures. Lighting has so many options to look at, due to the area classification lighting can be very expensive with spray booth EX rated lights starting from $1563 each! Compliant lighting can be hard to achieve in a paint booth, make sure you get some good advice from a hazardous electrician or engineer. Yes, periodically filters should be replaced and ducts should be inspected for obstructions. This will ensure proper air flow which will reduce the risk of vapor buildup.
What Can I Use As A Spray Booth?
If the plastic doesn't cover the front, you may need to get another sheet of plastic to cover the front. To clean up the ends of the pipe, rub them down with a sanding block. Choose and apply the perfect finish for your project. This is important for both your safety and the quality of your work.

I used medium sized spring clamps to hold the plastic onto the spray booth frame. Here’s a view of the plastic curtain walls I hung in my shop. The floor is also covered with plastic, as the over spray can land on the floor. If you have a nice epoxy coating on the floor, you might want to consider protecting it like I did here. An advantage of creating a plastic sheeting curtain-wall paint area, is you can make it as big as your garage if you want.
The higher the ML count, the thicker the sheeting, so I would recommend around 4-6 ML – it’s a solid thickness that will make a durable barrier. You’ll need enough for three sides of the canopy. The good news is that I have a great fresh air source with the door.

This product enables the Dayton Blower 6FHX9 to be vented using standard 4" inch diameter circular duct. This adapter can be used with rigid, semi-rigid or flex duct. Also, we have received positive feedback about the blower from many readers that have used it in their booth. Pegboard is a great choice for mounting the prints as the machined holes allow excess overspray to run through.
A spray booth is a great investment for any furniture maker. It can help you save time and money while producing a high-quality product. Not only will it protect your work area and furniture, but it will also give you a more professional appearance. If you are considering building your spray booth, follow the instructions in this article to create a safe and effective space for finishing your furniture projects. If the PVC pipe is too long, you can always cut it down to size.
Pre-engineered spray booths can be purchased in a high-quality shop from a reputable manufacturer. A spray booth is a great option if you’re looking for a way to protect your furniture from paint fumes. By following these simple steps, you can build your spray booth that will keep your furniture looking its best. Are you a woodworker who wants to start spraying finishes? Having your own spray booth is essential when it comes to spraying finishes.
This summer I saved up some of what I made from teaching and bought a nice HVLP system. (FujiSpray Mini-Mite 4 with Gravity Fed Gun — more on that in a future post). With a nice HVLP I figured I could cut down on the amount of time I spend sanding a finish as each finish coat will generally go on faster and flatter with the spray gun. You’ll want to save this step until you’ve completed the bodywork and priming, and are ready for color. To create a temporary curtain wall or makeshift spray booth, you’ll need a 100-foot roll of 4- to 6-mil plastic.
